View Profile: cv2065 - Factory Five Forums

04-29-2026, 09:47 PM

cv2065 replied to a thread Need Wide Band A/F Gauge Advice in Roadster

I'm looking at this one. BT and goes to your phone. https://pe-ltd.com/product/wideband/

7 replies | 138 view(s)

04-28-2026, 04:38 PM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

Thanks Mike. I don't think I can go that low. Starts up and idles great at 16 but I think I can get more without detonation as the all in number is...

478 replies | 111998 view(s)

04-28-2026, 03:50 PM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

Another carb update. I'm currently running at the following: Initial Timing: 16 BTDC Mechanical Advance: 13 degrees Vacuum Advance: 12 degrees...

478 replies | 111998 view(s)

04-27-2026, 05:49 PM

cv2065 replied to a thread Carberator Hesitation in Roadster

Are you on timed or manifold vacuum? Seems like many crate engine builders like BP, Roush, etc., default to timed.

16 replies | 492 view(s)

04-26-2026, 01:49 PM

cv2065 replied to a thread Fun with Carbs in Roadster

Just made a few of those changes myself. Playing with moving from timed to manifold, but not there yet. ;) The lope on this engine is amazing.

6 replies | 222 view(s)

04-26-2026, 10:21 AM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

Looks like this new hanger is about 4" long while the old is 3". I figured one could take the 1" of slack out with the turn buckle, depending of...

478 replies | 111998 view(s)

04-25-2026, 11:00 PM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

As an update to my fuel issue, I made some float and accelerator pump arm adjustments. We'll test it out tomorrow. Roush recommends Ported vacuum...

478 replies | 111998 view(s)

04-25-2026, 10:53 PM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

I bought these heat shields a while back from Backdraft. I had them ceramic coated the same color as the pipes. Easy enough to install just as long...

478 replies | 111998 view(s)

04-25-2026, 10:41 PM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

I continue to finish up small things on the final punch. Visors were on the list next. I'm not sure exactly how functional these are, but I like how...

478 replies | 111998 view(s)

04-25-2026, 01:34 PM

cv2065 replied to a thread IRS center section install in Roadster

I put my first one in by myself with little issue. The second time I had my son and wife out to help balance it in the frame. And then it got stuck,...

11 replies | 300 view(s)

04-21-2026, 03:55 PM

cv2065 replied to a thread Mark IV wins Platnium in Roadster

Congrats! That's about 20 mins from my house. I used to go to it all the time before I sold my last build. You have to be careful down there as some...

12 replies | 437 view(s)

04-19-2026, 02:42 PM

cv2065 replied to a thread John in KC - Roadster Build Thread in Roadster Build Threads

Agreed. I changed my clutch out to the Tilton as it's the hardest to get to (thanks Mike :D). That said, I think a Tilton will be harder to replace...

203 replies | 33179 view(s)

04-19-2026, 12:16 PM

cv2065 replied to a thread John in KC - Roadster Build Thread in Roadster Build Threads

I guess you just have to remember that you are replacing all of these parts on the assumption that the kit supplied stuff is going to fail. Many have...

203 replies | 33179 view(s)

04-19-2026, 11:34 AM

cv2065 replied to a thread John in KC - Roadster Build Thread in Roadster Build Threads

I have one as well. At $93, Tilton is sure proud of that piece!

203 replies | 33179 view(s)

04-19-2026, 10:50 AM

cv2065 started a thread Fuel Pressure Regulator Question in Roadster

As I noted in my build thread, I came in from a drive yesterday and my fuel pressure gauge was reading 3-3.5psi and I was getting some surging while...

0 replies | 111 view(s)

04-19-2026, 01:00 AM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

I took the car out for a longer run today and boy was it hot, even after 7pm. Summer seems like it's going to be a beast. From a cooling perspective,...

478 replies | 111998 view(s)

04-19-2026, 12:49 AM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

On the last build, I secured the mirror to the dash using sheet metal screws. I didn't want to drill this time so used a bracket that I got from,...

478 replies | 111998 view(s)

04-19-2026, 12:44 AM

cv2065 replied to a thread CV2065 MKIV Roadster Build Thread #2 - Visors - Heat Shields - Saggy Pipe in Roadster Build Threads

Tackling the rest of the windshield odds and ends, which included the windshield trim brackets, rear view mirror, wind wings and visors. ...

478 replies | 111998 view(s)

04-18-2026, 08:28 AM

cv2065 replied to a thread Amazing MK4 Build on BaT in Roadster

Are you talking about 'The Cobra Story'? I have that book but only read a couple of chapters. A positive for all of us that FFR never folded as we'd...

20 replies | 571 view(s)

04-17-2026, 10:45 PM

cv2065 replied to a thread Amazing MK4 Build on BaT in Roadster

Superformance cars are authorized AND licensed by Shelby. Shelby authorizes the trademarks, trade dress and appearance of the car and Superformance...

20 replies | 571 view(s)

04-17-2026, 07:37 PM

cv2065 replied to a thread Amazing MK4 Build on BaT in Roadster

I looked at one at a car show and thought the same thing. Shelby authorized them but they do not get a global registration number with chassis built...

20 replies | 571 view(s)

04-17-2026, 06:10 PM

cv2065 replied to a thread Amazing MK4 Build on BaT in Roadster

That's a Superformance, not an FFR. They tend to bring more, why, I'm not so sure.

20 replies | 571 view(s)

04-17-2026, 10:46 AM

cv2065 replied to a thread Check your Blueprint Engine dipstick tube! in Roadster

You can reuse the drain plug just replace the copper crush washer. I never found one from a local jobber that fit. Always had leaks. Buy the pack of...

18 replies | 517 view(s)

04-16-2026, 06:52 PM

cv2065 replied to a thread Jesse builds a pickup #329 - Front cowl and hood in Build Threads - '35 Hot Rod Truck

Looks and sounds awesome Jessie. Loving those gauges.

156 replies | 19929 view(s)

04-16-2026, 02:12 PM

cv2065 replied to a thread 1 ¾" Trim Rings for Breeze Roll Bars? in Roadster

I had some custom ones made for $85 as I wanted some that were a little oversized. Any metal fabrication shop could easily do these. Just give them...

8 replies | 286 view(s)

04-16-2026, 08:18 AM

cv2065 replied to a thread Gas n performance closed? in Roadster

I ordered an extra set of gaskets and a girl from Gas N reached out to be sure I wasn’t stacking the gaskets for a pipe that maybe was misaligned....

80 replies | 4657 view(s)

04-14-2026, 09:06 PM

cv2065 replied to a thread John in KC - Roadster Build Thread in Roadster Build Threads

Looks great!

203 replies | 33179 view(s)