BluePrint Engines

Visit our community sponsor

Thanks Thanks:  0
Likes Likes:  1
Results 1 to 4 of 4

Thread: backup camera ideas

  1. #1
    25th Anniversary #9772 toadster's Avatar
    Join Date
    May 2011
    Location
    Folsom, CA
    Posts
    1,936
    Post Thanks / Like

    backup camera ideas

    Hey guys - I'm trying to figure out a backup camera scenario... yeah, I know these didn't exist on a '65 Cobra
    but I do have a touchscreen setup and have the backup camera capability - also ran the wires as well.

    I found a design from Saul (RIP) that I think is pretty novel, and hides the camera quite well...

    rear-camera.jpg rear-cam.jpg

    if you look closely, there's a recessed camera in the license plate frame where the lights reside - the camera is where the usual nut/bolt combo go to hold the frame onto the rubber seal against the trunk
    it seems that he used a few rivets to hold the setup now...

    does anyone have any ideas on how he accomplished this? I may just have to noodle a bit on it to make it work.

    the original idea was to use a license plate frame with a camera, but if the frame has the camera on top - it blocks the lights
    and if the camera is on the bottom, it blocks the trunk handle from opening

    51TiZbFlIvL._AC_SL1500_.jpg


    any other ideas?
    Todd
    25th Anniversary MkIV | #20 of 25 | Build #9772
    https://cobradreams.com/ <- my build!

  2. #2
    Senior Member
    Join Date
    Feb 2019
    Location
    Greality, Colorado
    Posts
    405
    Post Thanks / Like
    Todd, I am planning on doing the same as Saul did. As you noted (RIP Saul! I hope you’re driving the celestial highways at full throttle!) Saul, had the most optimal and for that matter, most elegant idea and implementation of adding a rear camera. Perhaps there was an electronic “pop-up” trunk lock, similar to doors that open with a remote switch? I suspect this was the solution and it is no doubt slick! There are various options on Summit or Amazon. I’ll be following along as I will be doing the same. You can do it, just need to route additional wires to make it happen.

    Doug
    Last edited by ydousurf; 07-09-2024 at 06:05 PM. Reason: Spelling
    Dj or Doug or TheLateDude
    ----- #19 of 25th Anniversary MKIV 9769 -----
    Build Link: https://thefactoryfiveforum.com/show...-Slow-Progress
    Ordered: Oct 07, 2019 / Production: Dec 28th, 2019 / Shipped: Jan 19th, 2019 First Start: In the future... / Graduation: Even further in the future...

  3. #3
    Senior Member
    Join Date
    Dec 2021
    Location
    Flower Mound TX
    Posts
    2,418
    Post Thanks / Like
    I eliminated the trunk handle and installed an electric latch from a 2001-2003 Ford Taurus I bought off eBay. It was really quite simple to install and is actuated with a button on the dash. There's also an emergency release cable hidden behind the license plate.









    My build thread https://thefactoryfiveforum.com/show...Roadster-Build

    Thread on Stainless Steel AN brake lines.
    Thread on fasteners and torque wrenches.
    Thread on Wilwood & Tilton master cylinders

  4. Likes ydousurf liked this post
  5. #4
    25th Anniversary #9772 toadster's Avatar
    Join Date
    May 2011
    Location
    Folsom, CA
    Posts
    1,936
    Post Thanks / Like
    Quote Originally Posted by ydousurf View Post
    Todd, I am planning on doing the same as Saul did. As you noted (RIP Saul! I hope you’re driving the celestial highways at full throttle!) Saul, had the most optimal and for that matter, most elegant idea and implementation of adding a rear camera. Perhaps there was an electronic “pop-up” trunk lock, similar to doors that open with a remote switch? I suspect this was the solution and it is no doubt slick! There are various options on Summit or Amazon. I’ll be following along as I will be doing the same. You can do it, just need to route additional wires to make it happen.

    Doug
    yeah, I have the wires already run it's just drilling and setting up that license plate holder properly

    I already have the trunk handle setup, so another option is probably out of the design at this point
    Todd
    25th Anniversary MkIV | #20 of 25 | Build #9772
    https://cobradreams.com/ <- my build!

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

FFMetal

Visit our community sponsor