View Profile: edwardb - Factory Five Forums

04-29-2026, 06:00 AM

edwardb replied to a thread Gen4X oil change oil quantity. in Ford Modular 5.0 "Coyote" Install and tuning

I've used the Moroso 20570 pan on several Coyote builds which I think is the most common one. I've found in all cases it took right at 10 quarts and...

3 replies | 69 view(s)

04-29-2026, 05:53 AM

edwardb replied to a thread Could use some help with my steering rack in Type '65 Coupe

I installed the PSC rack in my Mk5 build based on multiple recommendations. It is highly recommended to add rack extenders for the best front end...

12 replies | 147 view(s)

04-28-2026, 09:08 AM

edwardb replied to a thread EdwardB’s Mk5 30th Anniversary Build. Another Wiring Update in Roadster Build Threads

Been plugging away on the chassis wiring. Lots going on with Sharon’s knee rehab and now we have several major home improvement projects underway....

421 replies | 181276 view(s)

04-28-2026, 08:32 AM

edwardb added 4 photo(s) to album Mk5 Roadster Electrical

04-28-2026, 06:52 AM

Namrups replied to a thread Type65 - Enclosed Car Trailer in Type '65 Coupe

Check with EdwardB (Paul). He had a writeup about his trailer in his build thread. Scott

4 replies | 116 view(s)

04-27-2026, 07:11 PM

lewma started a thread Type65 - Enclosed Car Trailer in Type '65 Coupe

All Starting to look into an enclosed car trailer for my type65. Does anyone have experience with what sized enclosed trailer works well with...

4 replies | 116 view(s)

04-27-2026, 09:56 AM

lewma replied to a thread Lewma's Gen3 Coupe Almost Built Thread in Type '65 Coupe Build Threads

I used the gas pedal that came with the BluePrint GM427LS package. The mounting plate and pedal did need some trimming to get it to fit correctly. ...

101 replies | 15577 view(s)

04-27-2026, 07:59 AM

Namrups replied to a thread 3D Printed Parts in Roadster

The attachments are coming back as invalid. Scott

72 replies | 7998 view(s)

04-26-2026, 10:51 PM

edwardb replied to a thread spongy brakes, pedal goes to floor in Roadster

Everything you're describing is either air in the lines or a bad master cylinder. Anything else would have fluid coming out somewhere. I assume this...

21 replies | 490 view(s)

04-26-2026, 03:36 PM

460.465USMC replied to a thread Lugnut Mark’s type 65 build! in Type '65 Coupe Build Threads

Congrats, Mark!

200 replies | 17386 view(s)

04-26-2026, 02:39 PM

Ejzajac replied to a thread IRS center section install in Roadster

Thanks. I have the rear bolts temporaily threaded in safely, but had to remove the rear half of the rear bushings and the sleeves to get them...

11 replies | 300 view(s)

04-26-2026, 11:40 AM

460.465USMC replied to a thread Papa's Retirement Type 65 Coupe Build - Index in first post in Type '65 Coupe Build Threads

A new forum? Guess I'm out of the loop. Is this current forum being retired?

499 replies | 99090 view(s)

04-25-2026, 10:02 AM

edwardb replied to a thread Speedometer and speed sensor question in Roadster

There are two sets of speed sensor wires. Both from the same source. One in the dash harness and one in the sender harness. Just cap the sender ones...

14 replies | 229 view(s)

04-25-2026, 10:01 AM

edwardb replied to a thread IRS center section install in Roadster

I will only say, and you probably know this already, it's not easy to move. If you're anywhere near the holes to get the tapered bolt in there,...

11 replies | 300 view(s)

04-25-2026, 09:47 AM

Ejzajac replied to a thread IRS center section install in Roadster

Thanks Paul. My issue is that it is so snug between the bushings. I'll causiously pull out a rubber hammer for some gentle persuasion!

11 replies | 300 view(s)

04-25-2026, 06:15 AM

edwardb replied to a thread IRS center section install in Roadster

I've done several of these now. What's worked for me every time is once the lump is in place, get the rear bolts started. Far enough in to hold and...

11 replies | 300 view(s)

04-25-2026, 06:06 AM

edwardb replied to a thread Speedometer and speed sensor question in Roadster

I assume you're using the internal VSS on the RH side of the TKX. Very unlikely it's bad. The two wires from the TKX VSS are high signal and low...

14 replies | 229 view(s)

04-24-2026, 09:47 PM

Ejzajac replied to a thread IRS center section install in Roadster

Have been struggling with my IRS center section, but with a different problem! I positioned it solo with multiple ratchet straps, uneventfully. The...

11 replies | 300 view(s)

04-24-2026, 04:40 AM

edwardb replied to a thread IRS center section install in Roadster

This has been discussed a number of times and recently in this thread: https://thefactoryfiveforum.com/showthread.php?53500-IRS-Differential. You can...

11 replies | 300 view(s)

04-23-2026, 12:00 PM

GoDadGo replied to a thread No sidelines just dumping out the side. in Roadster

It Can Happen To Us All! https://youtu.be/GG2dF5PS0bI

30 replies | 958 view(s)

04-23-2026, 11:09 AM

GoDadGo replied to a thread No sidelines just dumping out the side. in Roadster

I ran some chambered race mufflers during testing that had a 3" inlet and outlet that were offset on both ends. https://youtu.be/PCngiKoopkA ...

30 replies | 958 view(s)

04-23-2026, 05:26 AM

edwardb replied to a thread Tim's Type 65 Build - Cockpit Wiring Finished? in Type '65 Coupe Build Threads

I'm a ways behind you on my Mk5 Roadster wiring. Still in the "mess" stage but getting better as I work through it. You're making good progress with...

470 replies | 93268 view(s)

04-22-2026, 01:52 PM

460.465USMC replied to a thread Chris' Coupe Build #566 - Rear Camera. EPBs. Hatch floor. in Type '65 Coupe Build Threads

I used something like that from Molex for the submerged splices on my in-tank fuel pump on this build. As I recall, they were pricey. Not bad if...

346 replies | 126033 view(s)

04-22-2026, 01:42 PM

460.465USMC replied to a thread Lugnut Mark’s type 65 build! in Type '65 Coupe Build Threads

I actually found the old order in my Amazon account: https://www.amazon.com/dp/B06XH7KJR1?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_3. No longer...

200 replies | 17386 view(s)

04-22-2026, 09:11 AM

Namrups replied to a thread John's Type 65 Build Thread in Type '65 Coupe Build Threads

Thank you Sir!! I believe my picture album is also public. Might be easier to find a pic there then going thru the build page by page. It's a really...

60 replies | 9483 view(s)

04-22-2026, 06:26 AM

edwardb replied to a thread Turbo's MK4 build adventure in Roadster Build Threads

Switch to a rounded head screw, turn it around so the head is on the inside, make sure the attachment clevis is oriented away from the coilover. Your...

49 replies | 9492 view(s)

04-21-2026, 09:23 PM

460.465USMC replied to a thread Lugnut Mark’s type 65 build! in Type '65 Coupe Build Threads

Congrats on First Start, Mark! Good to read about successful first starts on the Gen4x. I hope to get there...eventually. Regarding a clutch...

200 replies | 17386 view(s)