Street Rod Jim's 33 Hot Rod V2 #1143 Build - The Journey Begins

In this video I fiberglass in a area to hold a rivnut in place. Unfortunately a hard place to get into.


https://www.youtube.com/watch?v=9WA8wn7j5sU

Time to Cut & Buff The Firewall Paint of the 33 Hot Rod V2


https://www.youtube.com/watch?v=r3roD-Y1ZDg

Attempt two of cutting and buffing the firewall paint to get the deep scratches out.


https://www.youtube.com/watch?v=ju1aZr4cP8o&t=13s

Sanding the front bike fenders to get them ready for paint. 33 Hot Rod V2


https://www.youtube.com/watch?v=mc36uPvS28o

Knocking out some of the small nuances to get to the big stuff.


https://www.youtube.com/watch?v=tXRJSiQt75g

Firewall installation on the 33 Hot Rod V2


https://www.youtube.com/watch?v=gdrV8sWBUNU&t=5s

Installing the hood latch of the 33 Hot Rod V2


https://www.youtube.com/watch?v=6Qv0JfQyPZ0

Installing the floor panels and insulation on the 33 Hot Rod V2


https://www.youtube.com/watch?v=UKyEtXUThaI&t=2s

Navigating the door adjustments of the 33 Hot Rod V2.


https://www.youtube.com/watch?v=HZxFbuPW-FA&t=369s

Today I an working on finalizing all the bike fenders of the 33 Hot Rod V2. I thought I was done with the front fenders but i was told it was not good enough yet. Let's finish this.


https://www.youtube.com/watch?v=p9HBv2YV_Wg

Working on a hidden dash mount for the 33 Hot Rod V2


https://www.youtube.com/watch?v=vN4gIMfa0d4

Working the twist of out the doors. It takes Time, Time and more TIME!


https://www.youtube.com/watch?v=MM0w4c8hg9c

Installing the power windows of the 33 Hot Rod V2


https://www.youtube.com/watch?v=eNocxVAeJfs

Adding the side window glass into my 33 Hot Rod V2.


https://www.youtube.com/watch?v=HTeGvX5ISdU&t=54s

Installing the LS engine back into the FFR 33 Hot Rod V2.


https://www.youtube.com/watch?v=1D0TG4nn-H0

Verifying the pinon angle of the 33 Hot Rod V2.


https://www.youtube.com/watch?v=XvWv0LzdNPQ&t=2s

The official Lower control arm update for the 33 Hot Rod V2. Not!


https://www.youtube.com/watch?v=DcNkgjdb7TE&t=6s

Getting ready to wire the car, but I have to install the exhaust to make sure I have clearance.


https://www.youtube.com/watch?v=RWZirFri2GI

Wiring the fuel pump and gas level sender of the 33 Hot Rod V2.


https://www.youtube.com/watch?v=CpFJLBIelaY

Installing the driveshaft of the 33 Hot Rod V2 with LS engine and 4L60e transmission.


https://www.youtube.com/watch?v=3GrHs-X_V4k

Installing a Holley Terminator X into the 33 Hot Rod V2 with LS engine and 4L60e transmission.


https://www.youtube.com/watch?v=6fMxA6Y7d-Y

Today I install my Eddie Motorsport S Drive System.


https://www.youtube.com/watch?v=d3sxBM6sGOM

Cleaning up the 33 Hot Rod Wiring Harness


https://www.youtube.com/watch?v=-6gXh-jAg04

A full dive into understanding, designing and testing the wiring system of the 33 hot Rod V2.


https://www.youtube.com/watch?v=UEKwUZQr-_I

I start making some mini harness to make some clean runs.


https://www.youtube.com/watch?v=ZcDqdsSHl3M

Door and Window Replay design.


https://www.youtube.com/watch?v=2nxhSMxfw0o

Today I dig into the Heater Control Valve Wiring.


https://youtu.be/sGBWHPN0zGc

Today I reroute the LS engine harness on the FFR 33 Hot Rod V2.


https://www.youtube.com/watch?v=fnZTU7kkK2g

I decided a while ago to make a center console and put all my switches and controls into it. Today I get to wire it all in to place.


https://www.youtube.com/watch?v=-ijR5YOA_Rg

Now that everything is prewired, I have to integrate it into the main harness for the Factory Five 33 Hot Rod V2.


https://www.youtube.com/watch?v=TeHptV63edE&t=8s

SInce I have limited room in the dash, I am making a custom harness to the back of the car for all my relays.


https://www.youtube.com/watch?v=da_x_5tcPfg&t=1s

Now that the harness is in, I can add the relays. These control the doors and windows of the FFR 33 Hot Rod V2.


https://www.youtube.com/watch?v=Tb49X2fsLvY

Finally I have to get the tail lights and other cables sorted it out in the trunk of the Factory Five 33 Hot Rod.


https://www.youtube.com/watch?v=G5k1jhnh_cI

Today I finalize my wheel spacers and cut the radiator lower hose.


https://www.youtube.com/watch?v=Beg9lDxfM6w&t=81s

I finally get to start adding my reservoirs and dipstick on the 33 Hot Rod


https://www.youtube.com/watch?v=neefaf1_fuo&t=16s

Today I wires up the trunk area of the 33 Hot Rod V2.


https://www.youtube.com/watch?v=OQhvTT03yQs&t=8s

Due to remote coils I have to custom make my ignition wires.


https://www.youtube.com/watch?v=aAO_Enjypd4

My LS driveshaft that fits a 33 Hot Rod V1 does not work for V2. It needs to be lengthened.


https://www.youtube.com/watch?v=ag-dObe_o2g

Today I am adding my trans cooler line on a 4l65e.


https://www.youtube.com/watch?v=ExjIBnykbUg

Adding custom reverse tail lights ot the FFR 33 Hot Rod V2.


https://www.youtube.com/watch?v=MP9FPbG90yM