View Profile: John B. - Factory Five Forums

04-29-2026, 06:00 AM

edwardb replied to a thread Gen4X oil change oil quantity. in Ford Modular 5.0 "Coyote" Install and tuning

I've used the Moroso 20570 pan on several Coyote builds which I think is the most common one. I've found in all cases it took right at 10 quarts and...

3 replies | 88 view(s)

04-29-2026, 05:53 AM

edwardb replied to a thread Could use some help with my steering rack in Type '65 Coupe

I installed the PSC rack in my Mk5 build based on multiple recommendations. It is highly recommended to add rack extenders for the best front end...

12 replies | 195 view(s)

04-28-2026, 09:08 AM

edwardb replied to a thread EdwardB’s Mk5 30th Anniversary Build. Another Wiring Update in Roadster Build Threads

Been plugging away on the chassis wiring. Lots going on with Sharon’s knee rehab and now we have several major home improvement projects underway....

421 replies | 181594 view(s)

04-28-2026, 08:32 AM

edwardb added 4 photo(s) to album Mk5 Roadster Electrical

04-26-2026, 10:51 PM

edwardb replied to a thread spongy brakes, pedal goes to floor in Roadster

Everything you're describing is either air in the lines or a bad master cylinder. Anything else would have fluid coming out somewhere. I assume this...

21 replies | 569 view(s)

04-25-2026, 10:02 AM

edwardb replied to a thread Speedometer and speed sensor question in Roadster

There are two sets of speed sensor wires. Both from the same source. One in the dash harness and one in the sender harness. Just cap the sender ones...

14 replies | 278 view(s)

04-25-2026, 10:01 AM

edwardb replied to a thread IRS center section install in Roadster

I will only say, and you probably know this already, it's not easy to move. If you're anywhere near the holes to get the tapered bolt in there,...

11 replies | 329 view(s)

04-25-2026, 06:15 AM

edwardb replied to a thread IRS center section install in Roadster

I've done several of these now. What's worked for me every time is once the lump is in place, get the rear bolts started. Far enough in to hold and...

11 replies | 329 view(s)

04-25-2026, 06:06 AM

edwardb replied to a thread Speedometer and speed sensor question in Roadster

I assume you're using the internal VSS on the RH side of the TKX. Very unlikely it's bad. The two wires from the TKX VSS are high signal and low...

14 replies | 278 view(s)

04-24-2026, 04:40 AM

edwardb replied to a thread IRS center section install in Roadster

This has been discussed a number of times and recently in this thread: https://thefactoryfiveforum.com/showthread.php?53500-IRS-Differential. You can...

11 replies | 329 view(s)

04-23-2026, 05:26 AM

edwardb replied to a thread Tim's Type 65 Build - Cockpit Wiring Finished? in Type '65 Coupe Build Threads

I'm a ways behind you on my Mk5 Roadster wiring. Still in the "mess" stage but getting better as I work through it. You're making good progress with...

470 replies | 94363 view(s)

04-22-2026, 06:26 AM

edwardb replied to a thread Turbo's MK4 build adventure in Roadster Build Threads

Switch to a rounded head screw, turn it around so the head is on the inside, make sure the attachment clevis is oriented away from the coilover. Your...

49 replies | 9561 view(s)

04-21-2026, 08:17 AM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

With the spacers in place, there's enough room for the outer portion of the joint (and the top of the shock) to move some degrees in every direction....

67 replies | 1837 view(s)

04-21-2026, 05:34 AM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

Yes, what you described for the spreader is correct. I couldn't find a picture so snapped a quick pic of mine. It's 7/16" diameter because that's...

67 replies | 1837 view(s)

04-20-2026, 09:44 PM

edwardb replied to a thread Hello all New to forum thinking seriously about building 35 truck in Welcomes and Introductions

I completed a 35 Hot Rod Truck a couple years ago. It was an interesting build. The extended cab version, now standard, came out after mine was...

3 replies | 112 view(s)

04-20-2026, 09:39 PM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

It's not unusual to have to tweak the length of the various spacers. For the upper mount, if they're not off a lot, you could spread the tabs...

67 replies | 1837 view(s)

04-20-2026, 01:52 PM

edwardb replied to a thread Gen 4 Coyote Wiring Questions in General Discussions

I think Tim covered it. But here are my responses FWIW. From two Gen2 and one Gen3 installations. But neither of what you're asking about changed...

8 replies | 162 view(s)

04-19-2026, 10:35 AM

edwardb replied to a thread Question about E brake handle parts in Roadster

That mod was originally documented in my 20th Anniversary Roadster build here:...

6 replies | 203 view(s)

04-18-2026, 10:04 PM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

Note that I had a brain cramp and mixed up what I pictured and your forged arms. Same as the forged arms in my Mk5 build. Fixed in my post. Still...

67 replies | 1837 view(s)

04-18-2026, 09:47 PM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

Back slowly away from the snap rings..... really. The picture is my Coupe. My Mk5 with the forged arms is the same.

67 replies | 1837 view(s)

04-18-2026, 09:29 PM

edwardb replied to a thread EdwardB’s Mk5 30th Anniversary Build. Another Wiring Update in Roadster Build Threads

Slim update today with no pictures. Couple weeks ago we swapped places in the garage with the Coupe and Mk5 so I could put the Coupe on the lift for...

421 replies | 181594 view(s)

04-18-2026, 09:27 PM

edwardb replied to a thread Need help ASAP in General Discussions

The long cold winters here in Michigan and we lose strength... What can I say. I just wouldn't think to try it with two. Well maybe that's if one of...

11 replies | 294 view(s)

04-18-2026, 08:54 PM

edwardb replied to a thread Question about E brake handle parts in Roadster

X3 to clean them up and finish. PC is OK if it's not heavy. Could affect how it fits together. I paint them.

6 replies | 203 view(s)

04-18-2026, 08:39 PM

edwardb replied to a thread Need help ASAP in General Discussions

I've received several kits from Cunningham Transport (Stewart) and the driver has always called the day before and then again when in range. I don't...

11 replies | 294 view(s)

04-18-2026, 08:22 PM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

Yes, you need to turn that front lower LCA bolt around. Later you'll be adding sheet metal and the bolt will be trapped if installed in that...

67 replies | 1837 view(s)

04-17-2026, 10:44 PM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

Just the small/shorter ones from the set go on the upper ball joint. The ones on the lower control arms aren't easily replaced and in my experience...

67 replies | 1837 view(s)

04-17-2026, 04:43 PM

edwardb replied to a thread TN Father and Son Coupe Build - Need to grind spacers for Konis? in Type '65 Coupe Build Threads

The discussion about changing ball joints is the upper ones. They are screwed in. Not pressed in. I one of the lucky ones who has never had good luck...

67 replies | 1837 view(s)

John B.

Mini Statistics

More 1 Friend

edwardb

Recent Visitors

Basic Information

About John B.

Statistics

Total Posts

General Information

1 Friend

edwardb