View Full Version : Under Dash ideas
I want to place the Fueltech controller and battery main disconnect under the dash at the transmission tunnel.
I searched the forum but could not find any thread about it.
Does someone have any mods / builds about this? (basically adding a second dash at the tunnel to create a base for instruments / switches
https://thefactoryfiveforum.com/attachment.php?attachmentid=164565&d=1648307866
SJDave
03-26-2022, 01:18 PM
Here's an example of what I did, fabricated a sheet metal box, cut the tunnel aluminum off so I could remove the shifter area back without removing the new console. The console screws on to tabs welded to the frame rails. I can send you drawing of the console sheet metal to give you an idea how big and angles, but a starting point for you. PM with you Email and I'll send the drawing files.
I added 3/4" thick marine plywood on the shifter section to add cup holders and clear the TKO; used the original aluminum on the bottom surface for fire protection.
Love that dash!!
Cheers,
Dave
PM sent! tks Dave, exactly what I was looking for!
While I didn't add switches or gauges, I made a console to house the radio and a cubby for sunglasses or phone. On the PS, there is a USB and cigarette lighter power port. On the DS, there is a latching door to access the battery main disconnect.
164582
...and here it is right side up. :p
164583
Wayne r mckee
03-26-2022, 10:33 PM
164603164604
Here’s what I did , added charger ports and a couple of switches.
Otee453
03-26-2022, 11:52 PM
164610164609164608
CaptB
03-27-2022, 07:12 AM
Are there any aftermarket vendors that are selling any fabricated under dash consoles?
GoDadGo
03-27-2022, 07:28 AM
I built a "Do Dad" to hold my stereo and most of my switches and it turned out pretty well...The only problem is my car is so freaking loud that I don't use the stereo unless we parked...It also hides where most of my wires enter the engine bay so it's pretty busy to say the least.
https://thefactoryfiveforum.com/album.php?albumid=977&attachmentid=51774
You can see how it turned out around 1:51 into my graduation video:
https://youtu.be/9WEe6-wdNtA
I made mine form some .040 and a basic harbor freight bender. I had just enough room to mount my master battery disconnect switch on it. I also used the vintage toggle switch bezel for accessories.
https://thefactoryfiveforum.com/attachment.php?attachmentid=163917&d=1647266654
Thanks guys.. very helpful!!!
Blitzboy54
03-27-2022, 02:02 PM
Are there any aftermarket vendors that are selling any fabricated under dash consoles?
Yes, Whitby makes one. Check it out on their site. If you like it PM me. I purchased one and never used it. I’ll sell it for half price + shipping
toadster
12-22-2023, 04:35 PM
adding my lower dash ideas to the mix
knob in driver side is subwoofer gain
usb chargers both sides
seat heater buttons
footbox fan buttons
keyless start driver side
Wilwood Electric Parking Brake on passenger side
Alpine ilx-W650 (https://amzn.to/3vbqpDg) touchscreen stereo
Kenwood KAC-M3004 (https://amzn.to/3TwfaQ0) amp behind it all to power the 4 speakers in the car
https://i.ibb.co/myfCDrN/IMG-0346.jpg (https://ibb.co/VCfWj0w)
https://i.ibb.co/ZTZGqMj/IMG-0343.jpg (https://ibb.co/2KbWGk9)
cv2065
12-22-2023, 06:55 PM
adding my lower dash ideas to the mix
knob in driver side is subwoofer gain
usb chargers both sides
seat heater buttons
footbox fan buttons
keyless start driver side
Wilwood Electric Parking Brake on passenger side
Alpine ilx-W650 (https://amzn.to/3vbqpDg) touchscreen stereo
Kenwood KAC-M3004 (https://amzn.to/3TwfaQ0) amp behind it all to power the 4 speakers in the car
https://i.ibb.co/myfCDrN/IMG-0346.jpg (https://ibb.co/VCfWj0w)
https://i.ibb.co/ZTZGqMj/IMG-0343.jpg (https://ibb.co/2KbWGk9)
Toadster - What did you use to cut your dash holes?
BEAR-AvHistory
12-23-2023, 03:25 PM
Mine is pretty basic. Uses a Whitby consol kit. Easy to make with a Harbor break, but I did not have one at the time. Three versions using the same parts. Original with a radio, next the original with the AVH-4200-NEX. The third version is with custom gauges replacing the original FFR set. The vent pulls were also eliminated. Pretty much never used.
https://thefactoryfiveforum.com/attachment.php?attachmentid=193599&d=1703362911
Original version with radio.
https://thefactoryfiveforum.com/attachment.php?attachmentid=109991&d=1562111544
Second Version with the Pioneer receiver
https://thefactoryfiveforum.com/attachment.php?attachmentid=153848&d=1632788863
Third & current version also has custom gauges replacing the original FFR set. Vent pulls eliminated. Twin dual USB ports were added to the console.
FWIW I used velcro on the under dash tray to hold the garage door opener, 4200 controller & Nano I-pods
https://thefactoryfiveforum.com/attachment.php?attachmentid=116890&d=1572407344
All versions have the main speakers in them.
Tools were a step drill for small holes . An air powered nibbler to make the big holes.
https://thefactoryfiveforum.com/attachment.php?attachmentid=193600&d=1703363459
The kill switch is on the U-Joint cover. Easy to reach. I added a 10amp fuse to the switch to keep my ECU & 4200 alive when the switch is in the off position. Rubber shift boot was replaced by soft leather. Will not pull shifter out of gear.
toadster
01-03-2024, 06:53 PM
Toadster - What did you use to cut your dash holes?
I used hole saws for the bigger gauges, and regular drill bits, step bits, and even small hole saws for the buttons
high speed - light pressure, use a hepa vacuum and wear a mask - easy peasy
jklapp
01-04-2024, 09:40 PM
The vintage style switches are great. Where did you source them from? Thanks! Joel
I made mine form some .040 and a basic harbor freight bender. I had just enough room to mount my master battery disconnect switch on it. I also used the vintage toggle switch bezel for accessories.
https://thefactoryfiveforum.com/attachment.php?attachmentid=163917&d=1647266654