Elite Automotive
11-20-2011, 05:50 PM
2000 281 2V Valve Long block. PI heads with upgraded valve springs and stage 2 Anderson Cams. 10.2 to 1 compression. Made 496@ 12psi to the tire. The long block assembled by John Tymensky of Modular Performance. They used Federal Mogul HP series bearings, simply the most accurate for dimensional tolerances. ARP main studs, Manley rods with ARP2000 rod bolts, Diamond pistons that have offset piston pin makes for quieter operation in a forged piston.
MP machines all blocks (even brand new) for main bearing caps alignment, the cylinder deck surface for squareness, flatness and the proper finish for sealing, and bore (if required) and hone with plates. They also remove the front and rear oil galley cup plugs for block cleaning and then tap and install pipe plugs. Paid $8400.00 Asking $2900.00 obo
Mustang bullitt intake completely ported and polished runners. Very Nice piece, intake was new from Ford then sent out to get ported and polished. Then the outside was polished and powder coated with a translucent black. I will sell the complete conversion kit with alternator, accufab throttle body all brackets to convert a 2v intake. Over $2700 in port and polish work. $1500.00 obo
D&D performance Viper T-56 tranny. Fits 1999-2004 Best of everything and a Aston Martin .50 6th gear. With 4.10 gears at 70mph motor was at 1100 rpms. Will sell with bell housing, Spec stage 3 (I think) clutch, cross member and driveshaft. Paid $5400. Asking $2900.0 OBO
Vortech T trim for a mod motor. Just bought head unit from Dez performance. Has dyno time and one weekend at the track. I am willing to sell as a complete kit with 60# injectors 90mm mass air weldon fuel pump vortech blow off valve and a intercooler. Also have a canton pan drilled. Comes with oil lines and hardware. $3000.00
Accufab 75mm throttle body $120
BBK 75mm Throttle body and C&L Intake $190
2003 13" Calipers, brackets, new Wagner rotors and new Wagner Pads $400 obo
Eibach Pro-Kit Springs Part #47500 79-04 Mustang Fronts are new never on car Rears have part of a summer on them $125
Granatelli rear lower control arms $100
Vortech 8F103-021 Fuel rail mocked up never ran $100
FMS 30# Injectors used $150
Stock set of PI heads with cams Best offer
MP machines all blocks (even brand new) for main bearing caps alignment, the cylinder deck surface for squareness, flatness and the proper finish for sealing, and bore (if required) and hone with plates. They also remove the front and rear oil galley cup plugs for block cleaning and then tap and install pipe plugs. Paid $8400.00 Asking $2900.00 obo
Mustang bullitt intake completely ported and polished runners. Very Nice piece, intake was new from Ford then sent out to get ported and polished. Then the outside was polished and powder coated with a translucent black. I will sell the complete conversion kit with alternator, accufab throttle body all brackets to convert a 2v intake. Over $2700 in port and polish work. $1500.00 obo
D&D performance Viper T-56 tranny. Fits 1999-2004 Best of everything and a Aston Martin .50 6th gear. With 4.10 gears at 70mph motor was at 1100 rpms. Will sell with bell housing, Spec stage 3 (I think) clutch, cross member and driveshaft. Paid $5400. Asking $2900.0 OBO
Vortech T trim for a mod motor. Just bought head unit from Dez performance. Has dyno time and one weekend at the track. I am willing to sell as a complete kit with 60# injectors 90mm mass air weldon fuel pump vortech blow off valve and a intercooler. Also have a canton pan drilled. Comes with oil lines and hardware. $3000.00
Accufab 75mm throttle body $120
BBK 75mm Throttle body and C&L Intake $190
2003 13" Calipers, brackets, new Wagner rotors and new Wagner Pads $400 obo
Eibach Pro-Kit Springs Part #47500 79-04 Mustang Fronts are new never on car Rears have part of a summer on them $125
Granatelli rear lower control arms $100
Vortech 8F103-021 Fuel rail mocked up never ran $100
FMS 30# Injectors used $150
Stock set of PI heads with cams Best offer