Lokar cable clevis

[Chilly]

Can anyone point me in the direction to get the clevis for the e-brake re-routing, tried Summit but the site says not available. Greatly appreciate it.

Chilly

[Papa]

Lokar isn't selling it as a separate part anymore.

[65 Cobra Dude]

I may have some Chilly, I’ll check in the shop tomorrow. Got your PM as well.

Henry

[65 Cobra Dude]

Is this what you need? If so, PM me your address and I’ll send out tomorrow.

134033

Henry

[phileas_fogg]

Is this what you need? If so, PM me your address and I’ll send out tomorrow.

Henry

This is what I love about this community...so many folks willing & able to help a fellow builder out.


John

[Chilly]

Is this what you need? If so, PM me your address and I’ll send out tomorrow.

134033

Henry

Henry,

No, the one I am looking for are the ones that enable you to cut the cables and run them on top of the 4" mainframe and use the pulley system . I think edward was the one that first used it in his build. Sorry for the confusion.

Chilly

[Chilly]

Papa,

Is it a part of a kit then.

Chilly

[Papa]

Papa,

Is it a part of a kit then.

Chilly

Yep - Comes with several different e-brake kits including this universal one:

https://www.lokar.com/ebrake-cables.html

I think you can sill buy the block portion separately, but not with the clevis. It may be easy to fab up your own clevis.

https://www.speedwaymotors.com/Lokar-S-8070-Parking-Brake-Connector-Block,274778.html

[achi]

Chilly,

Check out this thread, discussed recently. https://thefactoryfiveforum.com/showthread.php?36269-E-brake-mod-Lokar-clevis-part-S-8078-no-longer-available

I found S-8071, it has one extra piece included, but it is not a whole expensive brake kit. Call around to smaller shops that may have ordered one and they have it in stock.

Good luck.

Cheers,
Achi

[Chilly]

Thanks for the help everyone, I think I can find one from you suggestions and or fab one that works.

Chilly

[GTBradley]

Thanks for the help everyone, I think I can find one from you suggestions and or fab one that works.

Chilly
Good luck, Chilly. I finally found one from a member and may be installing it this weekend. I really don’t understand Lokar pulling it from their vendors, when they still make it for their cable kits.

[Papa]

Thanks for the help everyone, I think I can find one from you suggestions and or fab one that works.

Chilly

Looks like Wilwood has a very similar part (950-330-11485):

https://www.jegs.com/i/Wilwood/950/330-11485/10002/-1?gclid=Cj0KCQjwhIP6BRCMARIsALu9LflAORI4YFG3GUDS5Z j8YU7a2j1KS-jYqmD-9-yjKlvBlweZn54IRKMaAjzZEALw_wcB

[GTBradley]

Nice find, but whoa, are they proud of that part!.

[Papa]

Nice find, but whoa, are they proud of that part!.

Yeah -- Summit is more proud to be selling it than Jegs and Wilwood are. :rolleyes:

[RBachman]

Try here.
https://www.mcmaster.com/clevises/corrosion-resistant-clevis-rod-ends/

[Chilly]

Ordered the clevis block from Speedway per Papa's link, should be able to fabricate the rest.

[Greg K]

Here is a another source for the clevis only, http://www.controlcables.com/clevises-cs550/
Pins on page 2 http://www.controlcables.com/fork-clevises/?sort=featured&page=2

[Chilly]

Thank you for all of the information, greatly appreciated.

Chilly