Cleaning out parts!

[R. Button]

Over the years I seem to have collected boxes of parts!
Here is a list of what I have for sale - offers accepted


Electric fan - new $10.00 - SOLD
water recovery tank - plastic (new) from Breeze & a black metal one Metal one $10.00 Plastic $8.00 SOLD
Willowwood 7/8 master cylinder with small plastic tank $10.00
Pertronix Distributor w/separate coil $30.00 - SOLD
MSD 8588 Distributor -SOLD
No brand name distributor designed much like the Pertronix system w/separate coil $20.00 SOLD
Front grill from Breeze - For a Mark I - Mark III never installed it $10.00 - SOLD
Used Autoweld rear adjustable lower control arms - for shipping cost - SOLD
FFR rear lower control arms - for shipping costs - SOLD
Disk brakes setup for Ford Thunderbird rears and Basic ford fronts w/rotors - power coated red. $20.00 would deliver if needed - depending on distance - SOLD
A set of rear control arm bushings - 4 of them - for shipping costs
cleaned up front disk brake calipers from a 1990 Mustang GT with spindles and just one rotor - $20.00 SOLD
headlights - one pair of blue dot centers and some tail lights $10.00 for the pair - SOLD
A working HID set of head lights - worked great just as I travel a bit ;)
$15.00

I went with the LED light bulbs in the headlights now. Easier to get parts while on the road! Often times I switch parts on my car to be sure I can get parts while traveling. That affect the choices I make for what parts to use. Also means I sometime collect piles of parts that I have pulled off my car - not because of a problem but solely based on available parts on the road!

103369 103371 103372 103373 103376 103377

[bil1024]

PM sent on distributor

[Higgybulin]

PM sent

[davvet2]

PM sent

[R. Button]

replied to each.

I have three Distributors
MSD 8598 - unused by me - it has a large cap so would not work with my dual carb system - SOLD
Pertronix Flamethrower Ign II D130810 also unused by me - looks new with a new coil also
TSP ready to run distributor with a spare small diameter cap and rotor also a one of TSP's coils
https://www.topstreetperformance.com/products/ignition/distributors/ready-to-run-distributors/ready-to-run-ford-289-302-distributor.html

I never installed any of them as I stumbled on a Ford Bronco distributor for a 5.0L small cap that works with my duraspark ignition module.
As mentioned my criteria for parts is can I get a part quickly when on the road. So often pass up on performance for more of a stock part.

These are the two distributors I have with the coils

103562 103563

[R. Button]

I also found that I have a spare unused ballast and wiring harness for the HID lights! So it comes with 3 ballast and a spare wiring harness with the relay. The HID's are BRIGHT! I recently switched over to LED light bulbs as they now sell the H4 LED bulbs to insert into a headlight housing which means on the road if I blew out a light I can just pickup a basic H4 bulb and plug it in. The HID I had wired to allow me to do the same - unplug the HID bulb and plug in a regular bulb bypassing the ballast.


And by the way this is only one set of parts shelves. Am still cleaning up the other 2 shelves for the Traveler "Yard" Sale! :)

Found on the second shelf a spare HID bulb too! So here is a pic of all the parts with the instruction book that I found too!

103561

[R. Button]

The part I dislike... when I get multi people that want the same item... and I have to go by the time stamp when they say yes I want it.
but it's my only choice to be fair


Also keep in mind that these parts are for a Mark I and may or may not fit a Mark 4
Like the grill is for a Mark 1-3

[SBCobra]

Interested in the tail lights.

[R. Button]

two complete rear red ones.
I you are interested in them

103489

[HookedonFord]

Hi, I would like the "Used Autoweld rear adjustable lower control arms - for shipping cost" if they are still available.
Thanks, Jim

[R. Button]

Jim, the autowelds are still avaiable.
I sent you a message for address etc.

[scottamann]

PM sent on headlights and tail lights

[R. Button]

Scott, Lights are boxed up and will shipout tomorrow

[SBCobra]

Pm sent on distributor.

[davvet2]

PM sent on grille - again.

Thanks,

Jim

[R. Button]

jim,
found a box and also sent the measurements of the grill

[DOHCCOBRA]

Hi Ralph,

I am looking for a set of headlight trim rings, it looks like there might be some in one of the pictures, do you by chance have a set of them you are looking to sell?

[R. Button]

I'll check to see if I have some and let you know.
I may not now as I sold a bod of headlight hardware I had.